smartctl -t long -a /dev/sda2
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Samsung SSD 850 EVO 250GB
Serial Number: S21PNXBG629935F
LU WWN Device Id: 5 002538 d4026dd39
Firmware Version: EMT01B6Q
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Jun 26 16:43:27 2018 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 133) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 080 080 010 Pre-fail Always - 138
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 21197
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 44
177 Wear_Leveling_Count 0x0013 001 001 000 Pre-fail Always - 14518
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 080 080 010 Pre-fail Always - 138
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 096 096 010 Old_age Always - 26
183 Runtime_Bad_Block 0x0013 080 080 010 Pre-fail Always - 138
187 Reported_Uncorrect 0x0032 093 093 000 Old_age Always - 61310
190 Airflow_Temperature_Cel 0x0032 057 048 000 Old_age Always - 43
195 Hardware_ECC_Recovered 0x001a 001 001 000 Old_age Always - 61310
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
235 Unknown_Attribute 0x0012 099 099 000 Old_age Always - 15
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 686837459712
Warning! SMART ATA Error Log Structure error: invalid SMART checksum.
SMART Error Log Version: 1
ATA Error Count: 61310 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 61310 occurred at disk power-on lifetime: 21197 hours (883 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 27 e2 e0 Error: UNC
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
2f 00 01 30 08 00 e0 1c 01:39:46.047 READ LOG EXT
2f 00 01 13 00 00 e0 1c 01:39:46.047 READ LOG EXT
ef 10 02 00 00 00 e0 1c 01:39:46.047 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 1c 01:39:46.047 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 e0 1c 01:39:46.047 IDENTIFY DEVICE
Error 61309 occurred at disk power-on lifetime: 21197 hours (883 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 27 e2 e0 Error: UNC
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
2f 00 01 30 08 00 e0 1c 01:39:46.047 READ LOG EXT
2f 00 01 13 00 00 e0 1c 01:39:46.047 READ LOG EXT
ef 10 02 00 00 00 e0 1c 01:39:46.047 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 1c 01:39:46.047 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 e0 1c 01:39:46.047 IDENTIFY DEVICE
Error 61308 occurred at disk power-on lifetime: 21197 hours (883 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 27 e2 e0 Error: UNC 8 sectors at LBA = 0x00e227d0 = 14821328
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 20 00 93 20 e0 1c 01:39:46.046 READ DMA
2f 00 01 30 08 00 e0 1c 01:39:46.046 READ LOG EXT
2f 00 01 13 00 00 e0 1c 01:39:46.046 READ LOG EXT
ef 10 02 00 00 00 e0 1c 01:39:46.046 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 1c 01:39:46.046 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 61307 occurred at disk power-on lifetime: 21197 hours (883 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 27 e2 e0 Error: UNC
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
2f 00 01 30 08 00 e0 1c 01:39:46.046 READ LOG EXT
2f 00 01 13 00 00 e0 1c 01:39:46.046 READ LOG EXT
ef 10 02 00 00 00 e0 1c 01:39:46.046 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 1c 01:39:46.046 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 e0 1c 01:39:46.046 IDENTIFY DEVICE
Error 61306 occurred at disk power-on lifetime: 21197 hours (883 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 27 e2 e0 Error: UNC 8 sectors at LBA = 0x00e227d0 = 14821328
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 20 c0 98 b8 e0 1c 01:39:46.046 READ DMA
2f 00 01 30 08 00 e0 1c 01:39:46.046 READ LOG EXT
2f 00 01 13 00 00 e0 1c 01:39:46.046 READ LOG EXT
ef 10 02 00 00 00 e0 1c 01:39:46.046 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 1c 01:39:46.046 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Простой
