Как задействовать весь объем ОЗУ на сервере под управлением Debian?

Было подозрение, что не отображается часть ОЗУ, отданная под рамдиски (крутится xen с 4 доменами), но быть по количеству не сходится вроде. Хотя, может я не разобрался. Вот полный вывод dmesg.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-amd64 ([e-mail]) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.78-1
[ 0.000000] Command line: placeholder root=UUID=58af1b63-7e07-40f2-9570-544bde20bb4c ro quiet
[ 0.000000] Freeing 9f-100 pfn range: 97 pages freed
[ 0.000000] 1-1 mapping on 9f->100
[ 0.000000] 1-1 mapping on 7fbf4->7fc5f
[ 0.000000] 1-1 mapping on 7fcf2->7fedf
[ 0.000000] 1-1 mapping on 7fef2->7feff
[ 0.000000] 1-1 mapping on 7ff00->fffd0
[ 0.000000] Released 97 pages of unused memory
[ 0.000000] Set 525206 page(s) to 1-1 mapping
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] Xen: 000000000009fc00 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 000000007fbf4000 (usable)
[ 0.000000] Xen: 000000007fbf4000 - 000000007fc5f000 (reserved)
[ 0.000000] Xen: 000000007fc5f000 - 000000007fcf2000 (usable)
[ 0.000000] Xen: 000000007fcf2000 - 000000007fedf000 (ACPI NVS)
[ 0.000000] Xen: 000000007fedf000 - 000000007fef2000 (usable)
[ 0.000000] Xen: 000000007fef2000 - 000000007feff000 (ACPI data)
[ 0.000000] Xen: 000000007feff000 - 000000007ff00000 (usable)
[ 0.000000] Xen: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] Xen: 00000000fffc0000 - 00000000fffd0000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: /S3000AH, BIOS S3000.86B.02.00.0044.071120071047 07/11/2007
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7ff00 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped : 0 - 037fc000
[ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000007ff00000
[ 0.000000] 0000000000 - 007ff00000 page 4k
[ 0.000000] kernel direct mapping tables up to 7ff00000 @ bfd000-1000000
[ 0.000000] xen: setting RW the range fda000 - 1000000
[ 0.000000] RAMDISK: 01940000 - 037fc000
[ 0.000000] ACPI: RSDP 0x00000000000F0350 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 0x000000007FEFE120 0004C (v01 INTEL S3000AH 00000000 INTL 01000013)
[ 0.000000] ACPI: FACP 0x000000007FEFB000 000F4 (v03 INTEL S3000AH 00000000 MSFT 01000013)
[ 0.000000] ACPI: DSDT 0x000000007FEF6000 04922 (v01 INTEL S3000AH 00000000 MSFT 01000013)
[ 0.000000] ACPI: FACS 0x000000007FE89000 00040
[ 0.000000] ACPI: APIC 0x000000007FEF5000 00078 (v01 INTEL S3000AH 00000000 MSFT 01000013)
[ 0.000000] ACPI: WDDT 0x000000007FEF4000 00040 (v01 INTEL S3000AH 00000000 MSFT 01000013)
[ 0.000000] ACPI: MCFG 0x000000007FEF3000 0003C (v01 INTEL S3000AH 00000000 MSFT 01000013)
[ 0.000000] ACPI: ASF! 0x000000007FEF2000 0009F (v32 INTEL S3000AH 00000001 MSFT 01000013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] NUMA turned off
[ 0.000000] Faking a node at 0000000000000000-000000007ff00000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007ff00000
[ 0.000000] NODE_DATA [00000000764df000 - 00000000764e3fff]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[5] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fbf4
[ 0.000000] 0: 0x0007fc5f -> 0x0007fcf2
[ 0.000000] 0: 0x0007fedf -> 0x0007fef2
[ 0.000000] 0: 0x0007feff -> 0x0007ff00
[ 0.000000] On node 0 totalpages: 523306
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 994 pages reserved
[ 0.000000] DMA zone: 2933 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512214 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] BIOS bug: APIC version is 0 for CPU 0/0x0, fixing up to 0x10
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 5, version 255, address 0xfec00000, GSI 0-255
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 272
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007fbf4000 - 000000007fc5f000
[ 0.000000] PM: Registered nosave memory: 000000007fcf2000 - 000000007fedf000
[ 0.000000] PM: Registered nosave memory: 000000007fef2000 - 000000007feff000
[ 0.000000] Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:7ed00000)
[ 0.000000] Booting paravirtualized kernel on Xen
[ 0.000000] Xen version: 4.1.4 (preserve-AD)
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff880076200000 s78912 r8192 d23488 u524288
[ 0.000000] pcpu-alloc: s78912 r8192 d23488 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 515147
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: placeholder root=UUID=58af1b63-7e07-40f2-9570-544bde20bb4c ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Placing 64MB software IO TLB between ffff88006fc00000 - ffff880073c00000
[ 0.000000] software IO TLB at phys 0x6fc00000 - 0x73c00000
[ 0.000000] Memory: 1794748k/2096128k available (3438k kernel code, 2904k absent, 298476k reserved, 3301k data, 584k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:33024 nr_irqs:1024 16
[ 0.000000] xen: sci override: global_irq=9 trigger=0 polarity=0
[ 0.000000] xen: registering gsi 9 triggering 0 polarity 0
[ 0.000000] xen: --> pirq=9 -> irq=9 (gsi=9)
[ 0.000000] xen: acpi sci 9
[ 0.000000] xen: --> pirq=1 -> irq=1 (gsi=1)
[ 0.000000] xen: --> pirq=2 -> irq=2 (gsi=2)
[ 0.000000] xen: --> pirq=3 -> irq=3 (gsi=3)
[ 0.000000] xen: --> pirq=4 -> irq=4 (gsi=4)
[ 0.000000] xen: --> pirq=5 -> irq=5 (gsi=5)
[ 0.000000] xen: --> pirq=6 -> irq=6 (gsi=6)
[ 0.000000] xen: --> pirq=7 -> irq=7 (gsi=7)
[ 0.000000] xen: --> pirq=8 -> irq=8 (gsi=8)
[ 0.000000] xen: --> pirq=10 -> irq=10 (gsi=10)
[ 0.000000] xen: --> pirq=11 -> irq=11 (gsi=11)
[ 0.000000] xen: --> pirq=12 -> irq=12 (gsi=12)
[ 0.000000] xen: --> pirq=13 -> irq=13 (gsi=13)
[ 0.000000] xen: --> pirq=14 -> irq=14 (gsi=14)
[ 0.000000] xen: --> pirq=15 -> irq=15 (gsi=15)
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Xen: using vcpuop timer interface
[ 0.000000] installing Xen timer for CPU 0
[ 0.000000] Detected 2400.140 MHz processor.
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.28 BogoMIPS (lpj=9600560)
[ 0.004000] pid_max: default: 32768 minimum: 301
[ 0.004000] Security Framework initialized
[ 0.004000] AppArmor: AppArmor disabled by boot time parameter
[ 0.004000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.004000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.004000] Mount-cache hash table entries: 256
[ 0.004000] Initializing cgroup subsys cpuacct
[ 0.004000] Initializing cgroup subsys memory
[ 0.004000] Initializing cgroup subsys devices
[ 0.004000] Initializing cgroup subsys freezer
[ 0.004000] Initializing cgroup subsys net_cls
[ 0.004000] Initializing cgroup subsys blkio
[ 0.004000] Initializing cgroup subsys perf_event
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] ACPI: Core revision 20110623
[ 0.011407] Performance Events: unsupported p6 CPU model 15 no PMU driver, software events only.
[ 0.011544] NMI watchdog disabled (cpu0): hardware events not enabled
[ 0.011666] installing Xen timer for CPU 1
[ 0.011804] NMI watchdog disabled (cpu1): hardware events not enabled
[ 0.011912] installing Xen timer for CPU 2
[ 0.012017] NMI watchdog disabled (cpu2): hardware events not enabled
[ 0.012140] installing Xen timer for CPU 3
[ 0.012284] NMI watchdog disabled (cpu3): hardware events not enabled
[ 0.012314] Brought up 4 CPUs
[ 0.012430] devtmpfs: initialized
[ 0.014571] PM: Registering ACPI NVS region at 7fcf2000 (2019328 bytes)
[ 0.014571] Grant table initialized
[ 0.014571] print_constraints: dummy:
[ 0.014571] NET: Registered protocol family 16
[ 0.014571] ACPI: bus type pci registered
[ 0.014571] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
[ 0.014571] PCI: not using MMCONFIG
[ 0.014571] PCI: Using configuration type 1 for base access
[ 0.016460] bio: create slab at 0
[ 0.016460] ACPI: Added _OSI(Module Device)
[ 0.016460] ACPI: Added _OSI(Processor Device)
[ 0.016460] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.016460] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.016823] ACPI: EC: Look up EC in DSDT
[ 0.018924] ACPI: Interpreter enabled
[ 0.018928] ACPI: (supports S0 S1 S4 S5)
[ 0.018948] ACPI: Using IOAPIC for interrupt routing
[ 0.018972] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
[ 0.020471] PCI: MMCONFIG at [mem 0xf0000000-0xffffffff] reserved in ACPI motherboard resources
[ 0.020475] PCI: MMCONFIG for 0000 [bus00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000) (size reduced!)
[ 0.041180] ACPI: No dock devices found.
[ 0.041183] HEST: Table not found.
[ 0.041186] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.042171] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.044039] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.044043] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.044046] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.044048] pci_root PNP0A03:00: host bridge window [mem 0x000e0000-0x000effff] (ignored)
[ 0.044051] pci_root PNP0A03:00: host bridge window [mem 0xf8000000-0xfebfffff] (ignored)
[ 0.044054] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xf0000000] (ignored)
[ 0.044071] pci 0000:00:00.0: [8086:2778] type 0 class 0x000600
[ 0.044217] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 0.044351] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.044399] pci 0000:00:1c.4: [8086:27e0] type 1 class 0x000604
[ 0.044538] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.044584] pci 0000:00:1c.5: [8086:27e2] type 1 class 0x000604
[ 0.044716] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.044756] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 0.044838] pci 0000:00:1d.0: reg 20: [io 0x3080-0x309f]
[ 0.044893] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 0.044965] pci 0000:00:1d.1: reg 20: [io 0x3060-0x307f]
[ 0.045019] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 0.045091] pci 0000:00:1d.2: reg 20: [io 0x3040-0x305f]
[ 0.045145] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 0.045217] pci 0000:00:1d.3: reg 20: [io 0x3020-0x303f]
[ 0.045286] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 0.045318] pci 0000:00:1d.7: reg 10: [mem 0x88200400-0x882007ff]
[ 0.045461] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.045494] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 0.045611] pci 0000:00:1f.0: [8086:27b8] type 0 class 0x000601
[ 0.045745] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.045760] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[ 0.045831] pci 0000:00:1f.1: [8086:27df] type 0 class 0x000101
[ 0.045852] pci 0000:00:1f.1: reg 10: [io 0x30d8-0x30df]
[ 0.045868] pci 0000:00:1f.1: reg 14: [io 0x30ec-0x30ef]
[ 0.045883] pci 0000:00:1f.1: reg 18: [io 0x30d0-0x30d7]
[ 0.045898] pci 0000:00:1f.1: reg 1c: [io 0x30e8-0x30eb]
[ 0.045913] pci 0000:00:1f.1: reg 20: [io 0x30b0-0x30bf]
[ 0.045975] pci 0000:00:1f.2: [8086:27c0] type 0 class 0x000101
[ 0.046000] pci 0000:00:1f.2: reg 10: [io 0x30c8-0x30cf]
[ 0.046014] pci 0000:00:1f.2: reg 14: [io 0x30e4-0x30e7]
[ 0.046028] pci 0000:00:1f.2: reg 18: [io 0x30c0-0x30c7]
[ 0.046042] pci 0000:00:1f.2: reg 1c: [io 0x30e0-0x30e3]
[ 0.046056] pci 0000:00:1f.2: reg 20: [io 0x30a0-0x30af]
[ 0.046070] pci 0000:00:1f.2: reg 24: [mem 0x88200000-0x882003ff]
[ 0.046125] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.046150] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 0.046232] pci 0000:00:1f.3: reg 20: [io 0x3000-0x301f]
[ 0.046360] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.046447] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
[ 0.046571] pci 0000:03:00.0: [8086:108c] type 0 class 0x000200
[ 0.046606] pci 0000:03:00.0: reg 10: [mem 0x88180000-0x8819ffff]
[ 0.046629] pci 0000:03:00.0: reg 14: [mem 0x88100000-0x8817ffff]
[ 0.046653] pci 0000:03:00.0: reg 18: [io 0x2000-0x201f]
[ 0.046852] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.046939] pci 0000:03:00.3: [8086:108f] type 0 class 0x000700
[ 0.046971] pci 0000:03:00.3: reg 10: [io 0x2020-0x2027]
[ 0.046995] pci 0000:03:00.3: reg 14: [mem 0x881a1000-0x881a1fff]
[ 0.047215] pci 0000:03:00.3: PME# supported from D0 D3hot D3cold
[ 0.047294] pci 0000:03:00.4: [8086:108e] type 0 class 0x000c07
[ 0.047326] pci 0000:03:00.4: reg 10: [mem 0x881a0000-0x881a0fff]
[ 0.047350] pci 0000:03:00.4: reg 14: [io 0x2028-0x202b]
[ 0.047570] pci 0000:03:00.4: PME# supported from D0 D3hot D3cold
[ 0.047622] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.047651] pci 0000:00:1c.5: PCI bridge to [bus 03-03]
[ 0.047656] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.047662] pci 0000:00:1c.5: bridge window [mem 0x88100000-0x881fffff]
[ 0.047733] pci 0000:04:04.0: [1002:515e] type 0 class 0x000300
[ 0.047763] pci 0000:04:04.0: reg 10: [mem 0x80000000-0x87ffffff pref]
[ 0.047779] pci 0000:04:04.0: reg 14: [io 0x1000-0x10ff]
[ 0.047796] pci 0000:04:04.0: reg 18: [mem 0x88040000-0x8804ffff]
[ 0.047854] pci 0000:04:04.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[ 0.047902] pci 0000:04:04.0: supports D1 D2
[ 0.047933] pci 0000:04:05.0: [8086:1076] type 0 class 0x000200
[ 0.047967] pci 0000:04:05.0: reg 10: [mem 0x88020000-0x8803ffff]
[ 0.047983] pci 0000:04:05.0: reg 14: [mem 0x88000000-0x8801ffff]
[ 0.047999] pci 0000:04:05.0: reg 18: [io 0x1100-0x113f]
[ 0.048011] pci 0000:04:05.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[ 0.048074] pci 0000:04:05.0: PME# supported from D0 D3hot D3cold
[ 0.048147] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 0.048153] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.048158] pci 0000:00:1e.0: bridge window [mem 0x88000000-0x880fffff]
[ 0.048168] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x87ffffff 64bit pref]
[ 0.048171] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.048173] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[ 0.048208] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.048374] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.048482] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.048548] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.048611] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
[ 0.048692] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.048696] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.048698] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.052114] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.052197] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
[ 0.052281] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.052361] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.052441] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.052522] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.052612] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.052693] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.052737] xen/balloon: Initialising balloon driver.
[ 0.053433] xen-balloon: Initialising balloon driver.
[ 0.053523] vgaarb: device added: PCI:0000:04:04.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.053523] vgaarb: loaded
[ 0.053523] vgaarb: bridge control possible 0000:04:04.0
[ 0.053523] PCI: Using ACPI for IRQ routing
[ 0.056650] PCI: pci_cache_line_size set to 64 bytes
[ 0.056763] reserve RAM buffer: 000000000009f000 - 000000000009ffff
[ 0.056765] reserve RAM buffer: 000000007fbf4000 - 000000007fffffff
[ 0.056768] reserve RAM buffer: 000000007fcf2000 - 000000007fffffff
[ 0.056770] reserve RAM buffer: 000000007fef2000 - 000000007fffffff
[ 0.056772] reserve RAM buffer: 000000007ff00000 - 000000007fffffff
[ 0.057011] hpet clockevent registered
[ 0.057015] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.057019] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.057023] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.064621] Switching to clocksource xen
[ 0.066044] pnp: PnP ACPI init
[ 0.066060] ACPI: bus type pnp registered
[ 0.067044] pnp 00:00: [bus 00-ff]
[ 0.067047] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.067049] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.067051] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.067053] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.067056] pnp 00:00: [mem 0x000e0000-0x000effff window]
[ 0.067058] pnp 00:00: [mem 0xf8000000-0xfebfffff window]
[ 0.067061] pnp 00:00: [mem 0x80000000-0xf0000000 window]
[ 0.067113] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.067125] pnp 00:01: [mem 0xf0000000-0xf3ffffff]
[ 0.067127] pnp 00:01: [mem 0xfed13000-0xfed13fff]
[ 0.067130] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.067132] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.067134] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.067136] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.067138] pnp 00:01: [mem 0xfed20000-0xfed9ffff]
[ 0.067140] pnp 00:01: [mem 0x000c0000-0x000dffff]
[ 0.067142] pnp 00:01: [mem 0x000e0000-0x000fffff]
[ 0.067144] pnp 00:01: [io 0x0779-0x0780]
[ 0.067162] system 00:01: [io 0x0779-0x0780] has been reserved
[ 0.067166] system 00:01: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.067169] system 00:01: [mem 0xfed13000-0xfed13fff] has been reserved
[ 0.067172] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.067175] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.067178] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.067181] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.067184] system 00:01: [mem 0xfed20000-0xfed9ffff] has been reserved
[ 0.067187] system 00:01: [mem 0x000c0000-0x000dffff] could not be reserved
[ 0.067190] system 00:01: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.067193] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.067349] pnp 00:02: [io 0x0000-0x000f]
[ 0.067351] pnp 00:02: [io 0x0081-0x0083]
[ 0.067353] pnp 00:02: [io 0x0087]
[ 0.067355] pnp 00:02: [io 0x0089-0x008b]
[ 0.067357] pnp 00:02: [io 0x008f]
[ 0.067359] pnp 00:02: [io 0x00c0-0x00df]
[ 0.067361] pnp 00:02: [dma 4]
[ 0.067391] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.067402] pnp 00:03: [io 0x0070-0x0071]
[ 0.067404] pnp 00:03: [io 0x0074-0x0077]
[ 0.067407] xen: registering gsi 8 triggering 1 polarity 0
[ 0.067417] pnp 00:03: [irq 8]
[ 0.067445] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.067458] pnp 00:04: [io 0x00f0]
[ 0.067460] xen: registering gsi 13 triggering 1 polarity 0
[ 0.067465] pnp 00:04: [irq 13]
[ 0.067496] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.067507] pnp 00:05: [io 0x0061]
[ 0.067538] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.067550] pnp 00:06: [io 0x0500-0x053f]
[ 0.067552] pnp 00:06: [io 0x0400-0x047f]
[ 0.067554] pnp 00:06: [io 0x0092]
[ 0.067555] pnp 00:06: [io 0x0680-0x06ff]
[ 0.067557] pnp 00:06: [io 0x0010-0x001f]
[ 0.067559] pnp 00:06: [io 0x0072-0x0073]
[ 0.067561] pnp 00:06: [io 0x0080]
[ 0.067563] pnp 00:06: [io 0x0084-0x0086]
[ 0.067565] pnp 00:06: [io 0x0088]
[ 0.067567] pnp 00:06: [io 0x008c-0x008e]
[ 0.067569] pnp 00:06: [io 0x0090-0x009f]
[ 0.067620] system 00:06: [io 0x0500-0x053f] has been reserved
[ 0.067623] system 00:06: [io 0x0400-0x047f] could not be reserved
[ 0.067626] system 00:06: [io 0x0680-0x06ff] has been reserved
[ 0.067629] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.067668] pnp 00:07: [io 0x0060]
[ 0.067670] pnp 00:07: [io 0x0064]
[ 0.067717] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.067999] pnp 00:08: [io 0x03f0-0x03f5]
[ 0.068002] pnp 00:08: [io 0x03f0]
[ 0.068004] xen: registering gsi 6 triggering 1 polarity 0
[ 0.068009] pnp 00:08: [irq 6]
[ 0.068011] pnp 00:08: [dma 2]
[ 0.068080] pnp 00:08: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.068413] pnp 00:09: [io 0x03f8-0x03ff]
[ 0.068416] xen: registering gsi 4 triggering 1 polarity 0
[ 0.068421] pnp 00:09: [irq 4]
[ 0.068502] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.068543] pnp 00:0a: [mem 0xfec00000-0xfec000ff]
[ 0.068578] pnp 00:0a: Plug and Play ACPI device, IDs PNP0003 (active)
[ 0.068611] pnp: PnP ACPI: found 11 devices
[ 0.068613] ACPI: ACPI bus type pnp unregistered
[ 0.076442] PM-Timer failed consistency check (0x0xffffff) - aborting.
[ 0.076459] pci 0000:04:05.0: address space collision: [mem 0xfffe0000-0xffffffff pref] conflicts with 0000:04:04.0 [mem 0xfffe0000-0xffffffff pref]
[ 0.076464] PCI: max bus depth: 1 pci_try_num: 2
[ 0.076518] pci 0000:00:1c.5: BAR 15: assigned [mem 0x88300000-0x884fffff 64bit pref]
[ 0.076521] pci 0000:00:1c.4: BAR 14: assigned [mem 0x88500000-0x886fffff]
[ 0.076525] pci 0000:00:1c.4: BAR 15: assigned [mem 0x88700000-0x888fffff 64bit pref]
[ 0.076528] pci 0000:00:1c.4: BAR 13: assigned [io 0x4000-0x4fff]
[ 0.076531] pci 0000:00:1c.0: BAR 14: assigned [mem 0x88900000-0x88afffff]
[ 0.076535] pci 0000:00:1c.0: BAR 15: assigned [mem 0x88b00000-0x88cfffff 64bit pref]
[ 0.076538] pci 0000:00:1c.0: BAR 13: assigned [io 0x5000-0x5fff]
[ 0.076541] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.076545] pci 0000:00:1c.0: bridge window [io 0x5000-0x5fff]
[ 0.076553] pci 0000:00:1c.0: bridge window [mem 0x88900000-0x88afffff]
[ 0.076558] pci 0000:00:1c.0: bridge window [mem 0x88b00000-0x88cfffff 64bit pref]
[ 0.076568] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
[ 0.076572] pci 0000:00:1c.4: bridge window [io 0x4000-0x4fff]
[ 0.076579] pci 0000:00:1c.4: bridge window [mem 0x88500000-0x886fffff]
[ 0.076585] pci 0000:00:1c.4: bridge window [mem 0x88700000-0x888fffff 64bit pref]
[ 0.076594] pci 0000:00:1c.5: PCI bridge to [bus 03-03]
[ 0.076598] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.076605] pci 0000:00:1c.5: bridge window [mem 0x88100000-0x881fffff]
[ 0.076611] pci 0000:00:1c.5: bridge window [mem 0x88300000-0x884fffff 64bit pref]
[ 0.076622] pci 0000:04:05.0: BAR 6: assigned [mem 0x88060000-0x8807ffff pref]
[ 0.076625] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 0.076629] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.076636] pci 0000:00:1e.0: bridge window [mem 0x88000000-0x880fffff]
[ 0.076642] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x87ffffff 64bit pref]
[ 0.076658] xen: registering gsi 17 triggering 0 polarity 1
[ 0.076671] xen: --> pirq=17 -> irq=17 (gsi=17)
[ 0.076686] pci 0000:00:1c.0: setting latency timer to 64
[ 0.076694] xen: registering gsi 17 triggering 0 polarity 1
[ 0.076696] Already setup the GSI :17
[ 0.076705] pci 0000:00:1c.4: setting latency timer to 64
[ 0.076713] xen: registering gsi 16 triggering 0 polarity 1
[ 0.076720] xen: --> pirq=16 -> irq=16 (gsi=16)
[ 0.076731] pci 0000:00:1c.5: setting latency timer to 64
[ 0.076742] pci 0000:00:1e.0: setting latency timer to 64
[ 0.076747] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.076749] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
[ 0.076752] pci_bus 0000:01: resource 0 [io 0x5000-0x5fff]
[ 0.076754] pci_bus 0000:01: resource 1 [mem 0x88900000-0x88afffff]
[ 0.076757] pci_bus 0000:01: resource 2 [mem 0x88b00000-0x88cfffff 64bit pref]
[ 0.076759] pci_bus 0000:02: resource 0 [io 0x4000-0x4fff]
[ 0.076761] pci_bus 0000:02: resource 1 [mem 0x88500000-0x886fffff]
[ 0.076764] pci_bus 0000:02: resource 2 [mem 0x88700000-0x888fffff 64bit pref]
[ 0.076767] pci_bus 0000:03: resource 0 [io 0x2000-0x2fff]
[ 0.076769] pci_bus 0000:03: resource 1 [mem 0x88100000-0x881fffff]
[ 0.076771] pci_bus 0000:03: resource 2 [mem 0x88300000-0x884fffff 64bit pref]
[ 0.076774] pci_bus 0000:04: resource 0 [io 0x1000-0x1fff]
[ 0.076776] pci_bus 0000:04: resource 1 [mem 0x88000000-0x880fffff]
[ 0.076779] pci_bus 0000:04: resource 2 [mem 0x80000000-0x87ffffff 64bit pref]
[ 0.076781] pci_bus 0000:04: resource 4 [io 0x0000-0xffff]
[ 0.076784] pci_bus 0000:04: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.076937] NET: Registered protocol family 2
[ 0.078927] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.080638] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.083002] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.083654] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.083656] TCP reno registered
[ 0.083675] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.083707] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.083945] NET: Registered protocol family 1
[ 0.083991] xen: registering gsi 23 triggering 0 polarity 1
[ 0.084009] xen: --> pirq=23 -> irq=23 (gsi=23)
[ 0.084083] xen: registering gsi 19 triggering 0 polarity 1
[ 0.084090] xen: --> pirq=19 -> irq=19 (gsi=19)
[ 0.084126] xen: registering gsi 18 triggering 0 polarity 1
[ 0.084132] xen: --> pirq=18 -> irq=18 (gsi=18)
[ 0.084166] xen: registering gsi 16 triggering 0 polarity 1
[ 0.084168] Already setup the GSI :16
[ 0.084203] xen: registering gsi 23 triggering 0 polarity 1
[ 0.084205] Already setup the GSI :23
[ 1.684085] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 1.684259] pci 0000:04:04.0: Boot video device
[ 1.684267] PCI: CLS 64 bytes, default 64
[ 1.684325] Unpacking initramfs...
[ 1.724970] Freeing initrd memory: 31472k freed
[ 1.739053] audit: initializing netlink socket (disabled)
[ 1.739070] type=2000 audit(1462565834.115:1): initialized
[ 1.751226] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.751694] VFS: Disk quotas dquot_6.5.2
[ 1.751742] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.751831] msgmni has been set to 3566
[ 1.752035] alg: No test for stdrng (krng)
[ 1.752334] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.752338] io scheduler noop registered
[ 1.752340] io scheduler deadline registered
[ 1.752384] io scheduler cfq registered (default)
[ 1.752500] pcieport 0000:00:1c.0: setting latency timer to 64
[ 1.752697] pcieport 0000:00:1c.4: setting latency timer to 64
[ 1.752865] pcieport 0000:00:1c.5: setting latency timer to 64
[ 1.753053] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.753074] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.753076] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.753358] ERST: Table is not found!
[ 1.753360] GHES: HEST is not enabled!
[ 1.753773] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.774379] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.924948] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.925078] xen: registering gsi 19 triggering 0 polarity 1
[ 1.925084] Already setup the GSI :19
[ 1.925176] serial8250: skipping TxEn test for device [8086:108f] subsystem [8086:0000]
[ 1.946096] 0000:03:00.3: ttyS1 at I/O 0x2020 (irq = 19) is a 16550A
[ 1.946253] Linux agpgart interface v0.103
[ 1.946393] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.949382] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.949389] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.949543] mousedev: PS/2 mouse device common for all mice
[ 1.949600] rtc_cmos 00:03: RTC can wake from S4
[ 1.949738] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.949772] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 1.950002] TCP cubic registered
[ 1.950140] NET: Registered protocol family 10
[ 1.950685] Mobile IPv6
[ 1.950689] NET: Registered protocol family 17
[ 1.950693] Registering the dns_resolver key type
[ 1.950848] PM: Hibernation image not present or could not be loaded.
[ 1.950858] registered taskstats version 1
[ 1.951299] rtc_cmos 00:03: setting system clock to 2016-05-06 20:17:13 UTC (1462565833)
[ 1.951347] Initializing network drop monitor service
[ 1.951506] Freeing unused kernel memory: 584k freed
[ 1.951658] Write protecting the kernel read-only data: 6144k
[ 1.954142] Freeing unused kernel memory: 640k freed
[ 1.954596] Freeing unused kernel memory: 684k freed
[ 1.983241] udevd[62]: starting version 175
[ 2.011758] usbcore: registered new interface driver usbfs
[ 2.020908] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 2.020911] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 2.020963] xen: registering gsi 17 triggering 0 polarity 1
[ 2.020969] Already setup the GSI :17
[ 2.021001] e1000e 0000:03:00.0: setting latency timer to 64
[ 2.021169] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 2.021401] usbcore: registered new interface driver hub
[ 2.029161] SCSI subsystem initialized
[ 2.029306] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 2.029309] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 2.029348] xen: registering gsi 17 triggering 0 polarity 1
[ 2.029355] Already setup the GSI :17
[ 2.031763] usbcore: registered new device driver usb
[ 2.032553] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.032590] xen: registering gsi 23 triggering 0 polarity 1
[ 2.032596] Already setup the GSI :23
[ 2.032626] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.032631] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.032666] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.032692] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 2.032708] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.032884] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.036615] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 2.036660] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x88200400
[ 2.046485] libata version 3.00 loaded.
[ 2.060095] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.060124] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.060127] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.060130] usb usb1: Product: EHCI Host Controller
[ 2.060132] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 2.060134] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.060303] hub 1-0:1.0: USB hub found
[ 2.060308] hub 1-0:1.0: 8 ports detected
[ 2.060443] xen: registering gsi 23 triggering 0 polarity 1
[ 2.060449] Already setup the GSI :23
[ 2.060470] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.060475] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.060489] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.060529] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
[ 2.060575] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.060578] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.060580] usb usb2: Product: UHCI Host Controller
[ 2.060582] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 2.060584] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.060833] hub 2-0:1.0: USB hub found
[ 2.060838] hub 2-0:1.0: 2 ports detected
[ 2.060934] xen: registering gsi 19 triggering 0 polarity 1
[ 2.060938] Already setup the GSI :19
[ 2.060952] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.060956] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.060964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.061024] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
[ 2.061061] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.061063] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.061066] usb usb3: Product: UHCI Host Controller
[ 2.061068] usb usb3: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 2.061070] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.061203] hub 3-0:1.0: USB hub found
[ 2.061207] hub 3-0:1.0: 2 ports detected
[ 2.061287] xen: registering gsi 18 triggering 0 polarity 1
[ 2.061291] Already setup the GSI :18
[ 2.061304] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.061308] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.061316] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.061366] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[ 2.061402] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.061405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.061407] usb usb4: Product: UHCI Host Controller
[ 2.061409] usb usb4: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 2.061411] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.061539] hub 4-0:1.0: USB hub found
[ 2.061543] hub 4-0:1.0: 2 ports detected
[ 2.061623] xen: registering gsi 16 triggering 0 polarity 1
[ 2.061627] Already setup the GSI :16
[ 2.061640] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2.061644] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.061653] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 2.061703] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003020
[ 2.061739] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.061742] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.061744] usb usb5: Product: UHCI Host Controller
[ 2.061746] usb usb5: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 2.061748] usb usb5: SerialNumber: 0000:00:1d.3
[ 2.061877] hub 5-0:1.0: USB hub found
[ 2.061881] hub 5-0:1.0: 2 ports detected
[ 2.061970] ata_piix 0000:00:1f.1: version 2.13
[ 2.061996] xen: registering gsi 18 triggering 0 polarity 1
[ 2.062002] Already setup the GSI :18
[ 2.062062] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 2.062530] scsi0 : ata_piix
[ 2.062687] scsi1 : ata_piix
[ 2.063117] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x30b0 irq 14
[ 2.063120] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x30b8 irq 15
[ 2.063142] xen: registering gsi 19 triggering 0 polarity 1
[ 2.063145] Already setup the GSI :19
[ 2.063155] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.063191] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 2.063545] scsi2 : ata_piix
[ 2.063636] scsi3 : ata_piix
[ 2.065108] ata3: SATA max UDMA/133 cmd 0x30c8 ctl 0x30e4 bmdma 0x30a0 irq 19
[ 2.065111] ata4: SATA max UDMA/133 cmd 0x30c0 ctl 0x30e0 bmdma 0x30a8 irq 19
[ 2.067055] FDC 0 is a post-1991 82077
[ 2.139442] e1000e 0000:03:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:15:17:5d:cb:a9
[ 2.139446] e1000e 0000:03:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 2.139459] e1000e 0000:03:00.0: eth0: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF
[ 2.236717] ata3.00: ATA-8: ST3250310NS, SN05, max UDMA/133
[ 2.236721] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.240397] ata4.00: ATA-8: WDC WD2500AAKX-22ERMA0, 17.01H17, max UDMA/133
[ 2.240401] ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.248424] ata4.00: configured for UDMA/133
[ 2.252775] ata3.00: configured for UDMA/133
[ 2.252916] scsi 2:0:0:0: Direct-Access ATA ST3250310NS SN05 PQ: 0 ANSI: 5
[ 2.253167] scsi 3:0:0:0: Direct-Access ATA WDC WD2500AAKX-2 17.0 PQ: 0 ANSI: 5
[ 2.260091] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 2.260161] sd 2:0:0:0: [sda] Write Protect is off
[ 2.260164] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.260187] sd 3:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 2.260192] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.260251] sd 3:0:0:0: [sdb] Write Protect is off
[ 2.260253] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.260281] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.270305] sdb: sdb1
[ 2.270581] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 2.275232] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 2.275309] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 2.276416] sda: sda1
[ 2.276780] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.282662] e1000 0000:04:05.0: eth1: (PCI:33MHz:32-bit) 00:15:17:5d:cb:aa
[ 2.282667] e1000 0000:04:05.0: eth1: Intel(R) PRO/1000 Network Connection
[ 2.564087] usb 4-1: new low-speed USB device number 2 using uhci_hcd
[ 2.642445] md: md0 stopped.
[ 2.643982] md: bind
[ 2.644309] md: bind
[ 2.646518] md: raid1 personality registered for level 1
[ 2.646943] bio: create slab at 1
[ 2.647068] md/raid1:md0: active with 2 out of 2 mirrors
[ 2.647110] md0: detected capacity change from 0 to 249924943872
[ 2.670309] md0: unknown partition table
[ 2.736088] Refined TSC clocksource calibration: 2400.069 MHz.
[ 2.846447] usb 4-1: New USB device found, idVendor=04d9, idProduct=1702
[ 2.846452] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.846455] usb 4-1: Product: USB Keyboard
[ 2.846458] usb 4-1: Manufacturer:
[ 2.910786] input: USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input0
[ 2.910856] generic-usb 0003:04D9:1702.0001: input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.2-1/input0
[ 3.015541] input: USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input1
[ 3.015620] generic-usb 0003:04D9:1702.0002: input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.2-1/input1
[ 3.015636] usbcore: registered new interface driver usbhid
[ 3.015638] usbhid: USB HID core driver
[ 3.293440] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
[ 5.103777] udevd[355]: starting version 175
[ 5.411337] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 5.411345] ACPI: Sleep Button [SLPB]
[ 5.411432] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.411436] ACPI: Power Button [PWRF]
[ 5.482012] coretemp coretemp.0: Using relative temperature scale!
[ 5.482050] coretemp coretemp.0: Using relative temperature scale!
[ 5.482072] coretemp coretemp.0: Using relative temperature scale!
[ 5.482104] coretemp coretemp.0: Using relative temperature scale!
[ 5.494060] ipmi message handler version 39.2
[ 5.515742] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 5.521633] intel_rng: Firmware space is locked read-only. If you can't or
[ 5.521635] intel_rng: don't want to disable this in firmware setup, and if
[ 5.521636] intel_rng: you are certain that your system has a functional
[ 5.521637] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 5.530853] EDAC MC: Ver: 2.1.0
[ 5.533230] xen: registering gsi 19 triggering 0 polarity 1
[ 5.533236] Already setup the GSI :19
[ 5.540827] EDAC MC0: Giving out device to 'i3000_edac' 'i3000': DEV 0000:00:00.0
[ 5.540848] EDAC PCI0: Giving out device to module 'i3000_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
[ 5.561105] iTCO_vendor_support: vendor-support=0
[ 5.594025] IPMI System Interface driver.
[ 5.594045] ipmi_si 0000:03:00.4: probing via PCI
[ 5.594060] xen: registering gsi 16 triggering 0 polarity 1
[ 5.594065] Already setup the GSI :16
[ 5.594075] ipmi_si 0000:03:00.4: [mem 0x881a0000-0x881a0fff] regsize 1 spacing 1 irq 16
[ 5.594077] ipmi_si: Adding PCI-specified kcs state machine
[ 5.594107] ipmi_si: Trying PCI-specified kcs state machine at mem address 0x881a0000, slave address 0x0, irq 16
[ 5.601116] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 5.601217] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[ 5.601293] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.609671] leds_ss4200: no LED devices found
[ 5.662870] [drm] Initialized drm 1.1.0 20060810
[ 5.932112] ipmi_si: There appears to be no BMC at this location
[ 5.998542] [drm] radeon defaulting to kernel modesetting.
[ 5.998545] [drm] radeon kernel modesetting enabled.
[ 5.998634] xen: registering gsi 18 triggering 0 polarity 1
[ 5.998640] Already setup the GSI :18
[ 5.998921] [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x8086:0x348E).
[ 5.998969] [drm] register mmio base: 0x88040000
[ 5.998972] [drm] register mmio size: 65536
[ 6.002705] radeon 0000:04:04.0: VRAM: 128M 0x0000000080000000 - 0x0000000087FFFFFF (16M used)
[ 6.002709] radeon 0000:04:04.0: GTT: 512M 0x0000000060000000 - 0x000000007FFFFFFF
[ 6.002715] [drm] Detected VRAM RAM=128M, BAR=128M
[ 6.002717] [drm] RAM width 16bits DDR
[ 6.002801] [TTM] Zone kernel: Available graphics memory: 914064 kiB
[ 6.002804] [TTM] Initializing pool allocator
[ 6.002812] [TTM] Initializing DMA pool allocator
[ 6.002838] [drm] radeon: 16M of VRAM memory ready
[ 6.002841] [drm] radeon: 512M of GTT memory ready.
[ 6.002862] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 6.004206] [drm] radeon: ib pool ready.
[ 6.024615] [drm] PCIE GART of 512M enabled (table at 0x000000000A900000).
[ 6.024646] radeon 0000:04:04.0: WB disabled
[ 6.024650] [drm] fence driver on ring 0 use gpu addr 0x60000000 and cpu addr 0xffff88006e6a3000
[ 6.024654] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.024655] [drm] Driver supports precise vblank timestamp query.
[ 6.024669] [drm] radeon: irq initialized.
[ 6.024740] [drm] Loading R100 Microcode
[ 6.047872] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.065962] platform radeon_cp.0: firmware: agent aborted loading radeon/R100_cp.bin (not found?)
[ 6.066109] [drm:r100_cp_init] *ERROR* Failed to load firmware!
[ 6.066157] radeon 0000:04:04.0: failed initializing CP (-2).
[ 6.066206] radeon 0000:04:04.0: Disabling GPU acceleration
[ 6.066256] [drm] radeon: cp finalized
[ 6.066280] radeon 0000:04:04.0: ffff8800031af400 unpin not necessary
[ 6.066815] [drm] No valid Ext TMDS info found in BIOS
[ 6.066855] [drm] Radeon Display Connectors
[ 6.066857] [drm] Connector 0:
[ 6.066858] [drm] VGA
[ 6.066860] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 6.066863] [drm] Encoders:
[ 6.066865] [drm] CRT1: INTERNAL_DAC1
[ 6.066866] [drm] Connector 1:
[ 6.066869] [drm] DVI-D
[ 6.066870] [drm] HPD2
[ 6.066872] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 6.066875] [drm] Encoders:
[ 6.066877] [drm] DFP2: INTERNAL_DVO1
[ 6.079326] [drm] fb mappable at 0x80040000
[ 6.079328] [drm] vram apper at 0x80000000
[ 6.079329] [drm] size 786432
[ 6.079331] [drm] fb depth is 8
[ 6.079332] [drm] pitch is 1024
[ 6.079454] fbcon: radeondrmfb (fb0) is primary device
[ 6.241001] Console: switching to colour frame buffer device 128x48
[ 6.248671] fb0: radeondrmfb frame buffer device
[ 6.248673] drm: registered panic notifier
[ 6.248679] [drm] Initialized radeon 2.16.0 20080528 for 0000:04:04.0 on minor 0
[ 6.728532] EXT4-fs (md0): re-mounted. Opts: (null)
[ 7.141401] EXT4-fs (md0): re-mounted. Opts: errors=remount-ro
[ 7.458935] loop: module loaded
[ 7.521989] Event-channel device installed.
[ 8.198483] Adding 4095996k swap on /swapfile. Priority:-1 extents:4 across:4362236k
[ 9.537100] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.655817] Bridge firewalling registered
[ 9.676854] device eth0 entered promiscuous mode
[ 9.684001] ADDRCONF(NETDEV_UP): bridge0: link is not ready
[ 12.509040] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 12.509417] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.509442] bridge0: port 1(eth0) entering listening state
[ 12.509446] bridge0: port 1(eth0) entering listening state
[ 15.146412] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 15.148495] e1000: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 15.148777] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.235313] 8021q: 802.1Q VLAN Support v1.8
[ 15.235333] 8021q: adding VLAN 0 to HW filter on device eth0
[ 15.235341] 8021q: adding VLAN 0 to HW filter on device eth1
[ 15.296793] device vlan76 entered promiscuous mode
[ 15.299117] device eth1 entered promiscuous mode
[ 15.304465] br76: port 1(vlan76) entering listening state
[ 15.304472] br76: port 1(vlan76) entering listening state
[ 15.304710] ADDRCONF(NETDEV_UP): br76: link is not ready
[ 16.570227] device vlan77 entered promiscuous mode
[ 16.577906] br77: port 1(vlan77) entering listening state
[ 16.577914] br77: port 1(vlan77) entering listening state
[ 16.578164] ADDRCONF(NETDEV_UP): br77: link is not ready
[ 17.843699] device vlan78 entered promiscuous mode
[ 17.851404] br78: port 1(vlan78) entering listening state
[ 17.851412] br78: port 1(vlan78) entering listening state
[ 17.851660] ADDRCONF(NETDEV_UP): br78: link is not ready
[ 19.124706] device vlan79 entered promiscuous mode
[ 19.132402] br79: port 1(vlan79) entering listening state
[ 19.132411] br79: port 1(vlan79) entering listening state
[ 19.132662] ADDRCONF(NETDEV_UP): br79: link is not ready
[ 20.986475] RPC: Registered named UNIX socket transport module.
[ 20.986478] RPC: Registered udp transport module.
[ 20.986480] RPC: Registered tcp transport module.
[ 20.986482] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 21.012437] FS-Cache: Loaded
[ 21.081315] FS-Cache: Netfs 'nfs' registered for caching
[ 21.101244] Installing knfsd (copyright (C) 1996 [e-mail]).
[ 23.017666] XENBUS: Unable to read cpu state
[ 23.024015] XENBUS: Unable to read cpu state
[ 23.030544] XENBUS: Unable to read cpu state
[ 23.036770] XENBUS: Unable to read cpu state
[ 25.856087] eth1: no IPv6 routers present
[ 27.225496] device vif1.1 entered promiscuous mode
[ 27.226505] device vif1.0 entered promiscuous mode
[ 27.228460] ADDRCONF(NETDEV_UP): vif1.1: link is not ready
[ 27.229528] ADDRCONF(NETDEV_UP): vif1.0: link is not ready
[ 27.552047] bridge0: port 1(eth0) entering learning state
[ 27.553802] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 29.981655] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[ 29.987675] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[ 30.037799] ADDRCONF(NETDEV_CHANGE): vif1.0: link becomes ready
[ 30.037830] bridge0: port 2(vif1.0) entering listening state
[ 30.037840] bridge0: port 2(vif1.0) entering listening state
[ 30.054671] ADDRCONF(NETDEV_CHANGE): vif1.1: link becomes ready
[ 30.054706] br76: port 2(vif1.1) entering listening state
[ 30.054710] br76: port 2(vif1.1) entering listening state
[ 30.336094] br76: port 1(vlan76) entering learning state
[ 30.675061] device vif2.1 entered promiscuous mode
[ 30.675406] device vif2.0 entered promiscuous mode
[ 30.681347] ADDRCONF(NETDEV_UP): vif2.1: link is not ready
[ 30.682301] ADDRCONF(NETDEV_UP): vif2.0: link is not ready
[ 31.584084] br77: port 1(vlan77) entering learning state
[ 32.864082] br78: port 1(vlan78) entering learning state
[ 33.426576] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[ 33.433685] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[ 33.494114] ADDRCONF(NETDEV_CHANGE): vif2.0: link becomes ready
[ 33.494152] bridge0: port 3(vif2.0) entering listening state
[ 33.494156] bridge0: port 3(vif2.0) entering listening state
[ 33.512218] ADDRCONF(NETDEV_CHANGE): vif2.1: link becomes ready
[ 33.512252] br77: port 2(vif2.1) entering listening state
[ 33.512256] br77: port 2(vif2.1) entering listening state
[ 34.121645] device vif3.0 entered promiscuous mode
[ 34.126761] ADDRCONF(NETDEV_UP): vif3.0: link is not ready
[ 34.144104] br79: port 1(vlan79) entering learning state
[ 34.161573] device vif3.1 entered promiscuous mode
[ 34.165323] ADDRCONF(NETDEV_UP): vif3.1: link is not ready
[ 36.865597] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[ 36.874026] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[ 36.944576] ADDRCONF(NETDEV_CHANGE): vif3.0: link becomes ready
[ 36.944618] bridge0: port 4(vif3.0) entering listening state
[ 36.944623] bridge0: port 4(vif3.0) entering listening state
[ 36.963246] ADDRCONF(NETDEV_CHANGE): vif3.1: link becomes ready
[ 36.963269] br78: port 2(vif3.1) entering listening state
[ 36.963272] br78: port 2(vif3.1) entering listening state
[ 37.539137] device vif4.0 entered promiscuous mode
[ 37.544176] ADDRCONF(NETDEV_UP): vif4.0: link is not ready
[ 37.589228] device vif4.1 entered promiscuous mode
[ 37.594880] ADDRCONF(NETDEV_UP): vif4.1: link is not ready
[ 40.294143] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[ 40.303535] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[ 40.391683] ADDRCONF(NETDEV_CHANGE): vif4.0: link becomes ready
[ 40.391717] bridge0: port 5(vif4.0) entering listening state
[ 40.391721] bridge0: port 5(vif4.0) entering listening state
[ 40.411925] ADDRCONF(NETDEV_CHANGE): vif4.1: link becomes ready
[ 40.411948] br79: port 2(vif4.1) entering listening state
[ 40.411952] br79: port 2(vif4.1) entering listening state
[ 40.896084] vif1.1: no IPv6 routers present
[ 41.036080] vif1.0: no IPv6 routers present
[ 42.592073] bridge0: topology change detected, propagating
[ 42.592083] bridge0: port 1(eth0) entering forwarding state
[ 42.592396] ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 43.664075] vif2.0: no IPv6 routers present
[ 44.192097] vif2.1: no IPv6 routers present
[ 45.088080] bridge0: port 2(vif1.0) entering learning state
[ 45.088087] br76: port 2(vif1.1) entering learning state
[ 45.344074] br76: topology change detected, propagating
[ 45.344082] br76: port 1(vlan76) entering forwarding state
[ 45.344368] ADDRCONF(NETDEV_CHANGE): br76: link becomes ready
[ 46.624095] br77: topology change detected, propagating
[ 46.624103] br77: port 1(vlan77) entering forwarding state
[ 46.624400] ADDRCONF(NETDEV_CHANGE): br77: link becomes ready
[ 47.496074] vif3.0: no IPv6 routers present
[ 47.792082] vif3.1: no IPv6 routers present
[ 47.904089] br78: topology change detected, propagating
[ 47.904098] br78: port 1(vlan78) entering forwarding state
[ 47.904395] ADDRCONF(NETDEV_CHANGE): br78: link becomes ready
[ 48.544074] br77: port 2(vif2.1) entering learning state
[ 48.544085] bridge0: port 3(vif2.0) entering learning state
[ 49.184072] br79: topology change detected, propagating
[ 49.184080] br79: port 1(vlan79) entering forwarding state
[ 49.184377] ADDRCONF(NETDEV_CHANGE): br79: link becomes ready
[ 50.520070] vif4.1: no IPv6 routers present
[ 50.912084] vif4.0: no IPv6 routers present
[ 52.000077] bridge0: port 4(vif3.0) entering learning state
[ 52.000087] br78: port 2(vif3.1) entering learning state
[ 53.456073] bridge0: no IPv6 routers present
[ 55.392086] bridge0: port 5(vif4.0) entering learning state
[ 55.456074] br79: port 2(vif4.1) entering learning state
[ 56.321231] br76: no IPv6 routers present
[ 56.752086] br77: no IPv6 routers present
[ 58.320086] br78: no IPv6 routers present
[ 60.128077] bridge0: topology change detected, propagating
[ 60.128083] bridge0: port 2(vif1.0) entering forwarding state
[ 60.128099] br79: no IPv6 routers present
[ 60.128103] br76: topology change detected, propagating
[ 60.128108] br76: port 2(vif1.1) entering forwarding state
[ 63.584073] br77: topology change detected, propagating
[ 63.584083] bridge0: topology change detected, propagating
[ 63.584095] bridge0: port 3(vif2.0) entering forwarding state
[ 63.584102] br77: port 2(vif2.1) entering forwarding state
[ 67.040084] bridge0: topology change detected, propagating
[ 67.040090] bridge0: port 4(vif3.0) entering forwarding state
[ 67.040098] br78: topology change detected, propagating
[ 67.040102] br78: port 2(vif3.1) entering forwarding state
[ 70.432080] bridge0: topology change detected, propagating
[ 70.432086] bridge0: port 5(vif4.0) entering forwarding state
[ 70.496072] br79: topology change detected, propagating
[ 70.496077] br79: port 2(vif4.1) entering forwarding state
[ 5115.265782] bridge0: port 2(vif1.0) entering forwarding state
[ 5115.265899] device vif1.0 left promiscuous mode
[ 5115.265902] bridge0: port 2(vif1.0) entering disabled state
[ 5115.300735] br76: port 2(vif1.1) entering forwarding state
[ 5115.300855] device vif1.1 left promiscuous mode
[ 5115.300858] br76: port 2(vif1.1) entering disabled state
[ 5116.678691] device vif6.0 entered promiscuous mode
[ 5116.681750] ADDRCONF(NETDEV_UP): vif6.0: link is not ready
[ 5116.714735] device vif6.1 entered promiscuous mode
[ 5116.717860] ADDRCONF(NETDEV_UP): vif6.1: link is not ready
[ 5117.386279] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[ 5117.398116] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[ 5117.413288] ADDRCONF(NETDEV_CHANGE): vif6.0: link becomes ready
[ 5117.413329] bridge0: port 2(vif6.0) entering listening state
[ 5117.413333] bridge0: port 2(vif6.0) entering listening state
[ 5117.421444] ADDRCONF(NETDEV_CHANGE): vif6.1: link becomes ready
[ 5117.421463] br76: port 2(vif6.1) entering listening state
[ 5117.421467] br76: port 2(vif6.1) entering listening state
[ 5127.536084] vif6.0: no IPv6 routers present
[ 5127.888082] vif6.1: no IPv6 routers present
[ 5132.448086] bridge0: port 2(vif6.0) entering learning state
[ 5132.448096] br76: port 2(vif6.1) entering learning state
[ 5147.488080] bridge0: topology change detected, propagating
[ 5147.488086] bridge0: port 2(vif6.0) entering forwarding state
[ 5147.488097] br76: topology change detected, propagating
[ 5147.488100] br76: port 2(vif6.1) entering forwarding state
[66977.380484] nf_conntrack version 0.5.0 (8110 buckets, 32440 max)
[175845.668515] bridge0: port 5(vif4.0) entering forwarding state
[175845.668623] device vif4.0 left promiscuous mode
[175845.668626] bridge0: port 5(vif4.0) entering disabled state
[175845.689964] br79: port 2(vif4.1) entering forwarding state
[175845.690270] device vif4.1 left promiscuous mode
[175845.690273] br79: port 2(vif4.1) entering disabled state
[175847.042177] device vif7.0 entered promiscuous mode
[175847.044770] device vif7.1 entered promiscuous mode
[175847.045365] ADDRCONF(NETDEV_UP): vif7.0: link is not ready
[175847.048161] ADDRCONF(NETDEV_UP): vif7.1: link is not ready
[175847.723497] xen-blkback:ring-ref 8, event-channel 8, protocol 2 (x86_32-abi)
[175847.735161] xen-blkback:ring-ref 9, event-channel 9, protocol 2 (x86_32-abi)
[175847.751080] ADDRCONF(NETDEV_CHANGE): vif7.0: link becomes ready
[175847.751121] bridge0: port 5(vif7.0) entering listening state
[175847.751126] bridge0: port 5(vif7.0) entering listening state
[175847.757715] ADDRCONF(NETDEV_CHANGE): vif7.1: link becomes ready
[175847.757738] br79: port 2(vif7.1) entering listening state
[175847.757742] br79: port 2(vif7.1) entering listening state
[175857.856079] vif7.0: no IPv6 routers present
[175858.384066] vif7.1: no IPv6 routers present
[175862.752085] bridge0: port 5(vif7.0) entering learning state
[175862.784086] br79: port 2(vif7.1) entering learning state
[175877.792078] bridge0: topology change detected, propagating
[175877.792085] bridge0: port 5(vif7.0) entering forwarding state
[175877.792094] br79: topology change detected, propagating
[175877.792098] br79: port 2(vif7.1) entering forwarding state