Имеется установленная система (
rhel-server-6.4-x86_64-dvd.iso). Поверх которой установлен KVM (
инструкция по установке). Хост-машине и guest-машине назначены собственные IP-адреса, для этого по инструкции с хабра настроен мост br0. Все работает. Теперь надо сделать bridge over bonding.
Ставлю на хосте следующие настройки:
[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
HWADDR=f0:92:1c:0f:76:f8
MASTER=bond0
SLAVE=yes
ONBOOT=yes
[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
HWADDR=F0:92:1C:0F:76:FC
MASTER=bond0
SLAVE=yes
ONBOOT=yes
[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-bond0
DEVICE=bond0
ONBOOT=yes
BRIDGE="br0"
[root@server ~]# cat /etc/modprobe.conf
alias bond0 bonding
options bond0 mode=1 miimon=100
[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-br0
DEVICE="br0"
NM_CONTROLLED="no"
ONBOOT="yes"
TYPE="Bridge"
BOOTPROTO="static"
IPADDR="10.2.26.39"
GATEWAY="10.2.26.1"
MTU="1500"
NETMASK="255.255.255.0"
DEFROUTE="yes"
IPV4_FAILURE_FATAL="yes"
IPV6INIT="no"
NAME="System br0"
Проверяю:
[root@server ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: down
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:f8
Slave queue ID: 0
Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:fc
Slave queue ID: 0
eth0 в дауне. Хотя я ожидал увидеть нечто типа следующего:
[root@server ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:e8
Slave queue ID: 0
Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:ec
Slave queue ID: 0
Вопрос собственно в сабже, как настроить bridge over bonding в RHEL 6.4 Server?
