smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.16.0-30-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HGST HTS545050A7E680
Serial Number: TMA55C4T2WSSWL
LU WWN Device Id: 5 000cca 7aae8ce42
Firmware Version: GG2OAF10
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Jun 26 23:09:17 2015 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 114) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 075 075 062 Pre-fail Always - 111477163
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 253 253 033 Pre-fail Always - 0
4 Start_Stop_Count 0x0012 098 098 000 Old_age Always - 4592
5 Reallocated_Sector_Ct 0x0033 069 069 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 1919
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 3640
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 65536
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 217
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 8725
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 5/51)
196 Reallocated_Event_Count 0x0032 058 058 000 Old_age Always - 1164
197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 3792
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 3496 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3496 occurred at disk power-on lifetime: 1919 hours (79 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 70 00 00 00 40 00 00:10:44.966 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:44.965 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:44.965 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:44.964 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:44.964 SET FEATURES [Set transfer mode]
Error 3495 occurred at disk power-on lifetime: 1919 hours (79 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 68 00 00 00 40 00 00:10:41.442 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:41.441 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:41.441 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:41.440 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:41.440 SET FEATURES [Set transfer mode]
Error 3494 occurred at disk power-on lifetime: 1919 hours (79 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 60 00 00 00 40 00 00:10:37.910 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:37.909 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:37.909 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:37.908 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:37.908 SET FEATURES [Set transfer mode]
Error 3493 occurred at disk power-on lifetime: 1919 hours (79 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 58 00 00 00 40 00 00:10:34.386 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:34.386 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:34.385 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:34.384 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:34.384 SET FEATURES [Set transfer mode]
Error 3492 occurred at disk power-on lifetime: 1919 hours (79 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 50 00 00 00 40 00 00:10:30.854 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:30.854 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:30.853 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:30.852 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:30.852 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Средний
Средний
Средний
